CÔNG TY TNHH ITVC TOÀN CẦU

Ngôn ngữ: vien

0914 564 579

Hours: 8AM-17PM (T2-T7)


Đo lực - Sức căng - Sức nén

 Thiết bị đo lực nén Dillon X-C force gauge (10000kg)

Thiết bị đo lực nén Dillon X-C force gauge (10000kg)

 
GiáVND 


Chi tiết sản phẩm

THÔNG SỐ KỸ THUẬT:
 

Model: X-C Force Gauge
Part number: 30449-0014
Hãng sản xuất: Dillon
Xuất xứ: U.S.A
Bảo hành: 12 tháng
 
Dải đo: 10000 kg
Độ phân giải: 100 kg
Độ chính xác: ±1%
Qúa tải: 30% của dải đo.
Nhiệt độ hoạt động: đến 120° F
Vật liệu: được làm từ nhôm và thép hợp kim, sơn từ tính
Phụ kiện: HDSD
 

download datasheet

Principle of operation
A D-shaped deflection beam is the 
heart of the Dillon Force Gauge. 
Machined to close tolerances, beams 
are heat treated to develop optimum 
strength and spring characteristics. 
High-strength aluminum is used in 
Model X instruments through 500 
lb (200 kg). Ranges above this are 
fabricated from aircraft-quality 
alloy steel.
A precision dial indicator is mounted 
at the null point of the deflection 
beam. The indicator plunger rests 
against a slanted anvil at the open 
end of the beam, as shown in the 
photo. Under compression loads, 
the two halves of the beam tend to 
close. Tension force causes them to 
move apart. This action pushes the 
plunger inward, as determined by 
the slant of the anvil. Readings 
produced on the dial are in direct 
relation to applied load. The pointer 
revolves 360° clockwise under 
compression or tension forces. 
Push-pull gauges read half scale 
(180°) clockwise in compression, and 
counterclockwise, 180° from center 
zero under tension loads.
Low beam deflection
When measured across the center 
of top- and bottom-loading holes, 
the approximate beam deflection is 
as follows:
50 to 250-lb capacity  0.019"
(25 to 100 kg)
500-lb capacity  0.016"
(200 kg)
1,000-lb capacity  0.018"
(500 kg)
2,000-lb capacity  0.011"
(1000 kg)
5- and 10,000-lb capacity  0.010"
(2 and 5000 kg)
25,000-lb capacity  0.022"
(10,000 kg)
Overload rating
Accidental overloads up to 30% of 
capacity can be safely sustained 
without injury to the dial indicator 
or deflection beam. All capacities 
feature a 5:1 design safety factor.
General information
n  To reset zero, loosen knurled 
bezel-locking screw and rotate 
dial.
n  Dillon Model X Force Gauges may 
be mounted horizontally, vertically, 
or flat.
n  The baked-enamel finish resists 
corrosion and rust.
n  Operating temperature 
up to 120° F.

Sản phẩm liên quan



Copyright © 2014 ICTV. All Rights Reserved.

tư vấn iso, tu van iso, kiểm toán năng lượng, kiem toan nang luong

0914 564 579